Adhesives

A43 THREADLOCK (25ml / 50ml)

A medium viscosity, medium strength screw and threadlocker. Used as a locking compound for direct application to lightly oiled components.

Application: Replaces spring washers and locks nuts. Removable using the correct tools. Also prevents rusting or corrosion. Non-drip consistency for clean, economic application.

A70 STUDLOCK (25ml / 50ml)

A high strength, anaerobic adhesive. It is resistant to fuels, oils, hydraulic, and refrigeration fluids. Also acts as a lubricant during assembly to ensure accurate torquing and protection against corrosion. Prevents rusting or corrosion and cannot be dismantled once adhesive has set.

Application: For the permanent retention and sealing of threaded fasteners, sleeves and bearings.

AEROSOL SPRAY ADHESIVE (500ml)

A high strength spray adhesive for bonding carpet tiles and non structural applications. Gives exceptionally strong adhesion for a wide range of demanding uses. Fitted with a variable discharge spray that controls the width of the fan. DCM free.

Application: It is ideal for perimeter bonding of carpet tiles and minor flooring installations, and for use in the furniture and automotive industries, especially for bonding foam to a variety of surfaces. Also suitable for use in repair and non-structural applications where a high strength bond is required.

ANCHORBOND (380ml)

A polyester resin, 2-part, rapid curing, chemical anchoring system. Applied in one single action to produce a cost effective, tough chemical resistant fixing.

Application: Suitable for setting bolts, studs, wall ties, starter bars or large screws, etc. into a wide range of substrates. Compatible with brickwork, concrete, masonry, stone and aerated concrete blocks. Ideal for close-to-edge applications (unlike expansion anchors) as no stress is placed on the surrounding substrate. Full cure is obtained after 2 hours. Specialist extruder available for the 380ml cartridge; 310ml now fits standard sealant applicator gun.

CONTACT ADHESIVE (1L / 5L)

A premium grade, solvent-based, neoprene adhesive with high grab and long open time to enable re-positioning. This product is toluene-free!

Application: Can be used for bonding to cork, leather, rubber, metals, wood, chipboard, hardboard, laminated plastics (eg. Formica), dense textiles, plaster, stone, concrete, cementitious screeds and smoothing compounds. It will bond rigid PVC and PVCu sheets but the materials should be checked for suitability prior to application as plasticiser migration can occur in some instances. Note: This product is not suitable for polystyrene, polythene, polypropylene, silicone rubbers, bitumen or PTFE. The solvent in the contact adhesive may attack certain painted or lacquered surfaces. Test a small area of adhesive on the surfaces prior to full application.

PVA ADHESIVE & SEALER (500ml / 1L / 2.5L / 5L / 200L / 1000kg)

A high performance sealer, primer, dust-proofer and bonding agent. Improves adhesion and reduces cracking in cememts and plaster. Primes and seals porous surfaces. Quick drying, durable and has a very high bond strength. Conforms to BS5270.

Application: Plaster primer, porous surface primer and sealer. - Rendering key coat for internal applications. - Admixture. - Dust sealer. - General purpose adhesive for bonding all common construction materials. - Phthalate free formulation (safer to use).

CONTRACTORS GRADE PVA (500ml / 1L / 2.5L / 5L)

An all purpose, premium quality primer, sealer and bonding agent that dries quickly to a high bond strength. Conforms to BS5270.

Application: Can be used with plaster, cement, timber, gypsum wall boards and paper. Properties as an adhesive include fast drying. It is also a readily available dilutable primer for sealing applications or addition to cement and plaster to improve adhesion and cure. High solids content compared with other contractor grades. Solids content is all polymer - no fillers are used! Better water resistance. Better adhesion and flexibility. Better drying at low temperatures. Phthalate free formulation (safer to use).

DUO 2 IN 1 WOOD GLUE (125ml / 250ml / 500ml / 2.5L / 5L / 25L)

Developed using the latest fast drying, water resistant, PVA technology, this product achieves a bond strength stronger than the wood itself. A cost-effective, water-resistant wood adhesive that conforms to the requirements of category D3/3 and D3/4 of EN204. In addition, it also meets the resistance to sustained load (creep test) requirements of BS4071 ""Polyvynil Acetate (PVA) Emulsion Adhesives for Wood"".

Application: Designed as a one-pack ready-to-use adhesive which gives a fast rate of bond strength development. Suitable for hard and soft woods, decorative laminates, chipboard blockwood and other engineered timber panels. Can be used in applications where joints may be subjected to short term water contact or exposure to high humidity i.e. kitchen work surfaces, window frames, doors and stairs. Suitable for interior and exterior applications.

GB PRO HYBRID SEALANT (EU3) BL / CL / GR / WH

A high quality, high modulus sealing and bonding material. A totally neutral "hybrid" sealant for use in areas requiring a tough enough elastic rubber joint or as an adhesive with superior bonding strength. Conforms to ISO11600F&G-20HM. Properties. High modulus, remains permanently flexible. For sealing and bonding interior and exterior applications in all weather conditions. Can be over-painted. Non-staining (excellent for use on natural stone). Non-shrinking. Contains no isocyanates, solvents, silicone and phalates and is odourless. Rapid curing. Resistant to UV radiation, water (including sea water), mould and chlorine. Excellent adhesion to most surfaces (even wet surfaces). Will not discolour surfaces. Wet on wet application. Available in Black / Crystal Clear / Grey / White.

Application: Suitable for filling and sealing of : 1) connecting joints, cracks, holes, etc. in the building sector. 2) for wooden joints in ship decks. 3) for bonding metal to metal (can absorb vibration). 4) as a high quality glazing sealant including for use with burglar safe glazing systems. 5) as a universal waterproof construction adhesive for bonding stone, concrete, mirrors (with acetone resistant backing), natural stone, marble, gypsum board, polycarbonates, polystyrene, PVC, many plastics, ceramics, copper, lead, zinc, aluminium, stainless steel, wood and glass. For sealing and adhering shower trays, sinks, sanitary ware, drain pipes and much more. NOTE: This product is not recommended for use with expansion joints. Trade counter merchandising box available on request.

GRIPBOND ADHESIVE

A multi-purpose, synthetic rubber based construction adhesive that can replace mechanical fixings in a wide variety of domestic, commercial and industrial applications. A fast bonding, non-slumping, instant grab adhesive with good gap-filling properties even on uneven surfaces. It can be used in all weather conditions and is suitable for rough and porous surfaces. It can also be over-painted once dry. Bridges gaps up to 10mm.

Application: Ideal for fixing a wide variety of materials. It can be used to fix skirting boards, door surrounds and frames, window sills, all types of cladding, wall battens, decorative wall boards, metal carpet edges, automotive trims and much more. It can be used for interior and exterior applications. NOTE: this product is Toluene free! 

ECO XTREME SOLVENT FREE ADHESIVE

A premium environmentally friendly, multipurpose, gap-filling adhesive. Water based, totally solvent-free with quick grab properties. Cures to give a tough, durable and permanent bond.

Can be used to replace or augment mechanical fixings when bonding brick, building panels, carpets, chipboards, concrete, coving, floor panels, foam insulation, marble, metals, tiles and timber. It is also suitable for bonding polystyrene.

HVC HIGH VISCOSITY SUPERGLUE (20g)

A premium cyanoacrylate adhesive developed for bonding rubber and plastics including PVCu. A high viscosity superglue for use on porous surfaces. Comes with a resealable cap.

Application: Has gap-filling properties making it ideal for bonding trims and caps on PVCu windows as well as rubber, wood, metal, ceramics, leather, porcelain and card.

Contact Spray Adhesive

Contact Adhesive in an Aerosol. Not to be confused with Standard Carpet or Multi Purpose Adhesive. The first product from the new generation of synthetic rubber/resin adhesives.

Its high solids/low solvent formula produces a quicker, stronger , more aggressive bonding system which out performs all conventional aerosol adhesives, Ideal for bonding laminates, carpets, carpet tiles, most vinyl floor coverings, fabrics, foams and felts, pvc skirtings and much more. Suitable for a wide range of applications including contract flooring, building industry, shop and office fitting, furniture industry, laminating, joinery, insulation, and boat, coach & caravan fitting & refurbishment.

It has excellent high temperature resistance (80°C), therefore it is most suitable for many automotive and marine applications and anywhere a high temperature adhesive is required.

MEGA STIK PU ADHESIVE (750ml)

A fast curing, adhesive foam that has been specially developed for the rapid installation of plasterboard, insulation boards, floorboards and roof decking. Supplied in an aerosol can, the product can be used with a standard foam gun. A multi-purpose, polyurethane construction adhesive in a can - but not just a drywall adhesive. The cured adhesive is an excellent heat insulator and has exceptionally good adhesion properties. Can also be used to dampen sound.

Application: Adheres well to most building materials, with the exception of Teflon, polyethylene and silicone surfaces. Suitable for installing doors and windows, insulating and fixing pipes, filling holes and gaps, fixing wall panels, skirting boards, plaster board, roof tiles, decking and for thermal insulation. Benefits: No mixing, no mess, no water, no dust! No need to carry heavy bags of plaster. One can fixes approximately 5 standard plaster boards. 30% time saving over conventional dry wall adhesives. Can be plastered in 1 hour. Can be applied direct to boards or the wall. Works on solid walls, metal and timber studding. No nails or screws required!

MITRE PACK ADHESIVE (50g + 200ml)

A high strength bonding system comprising a cyanoacyrylate adhesive with an aerosol activator to ensure full and rapid curing on acid surfaces. Can be used for bonding MDF, wood, rubber and most plastics.

Application: Pack includes: 1 tin of activator (200ml) and 1 bottle of HVC Superglue (50g).

PU RAPIDGRIP 5 MINUTE (310ml)

One-part moisture cure polyurethane adhesives specially formulated for waterproofing bonding. These products are seawater proof and are resistant to acid and chemicals. Conforms to BS EN 204 (class D4). A solvent-free, rapid setting thixotropic translucent PU gel which sets in 5 minutes.

Application: Excellent bonding properties suitable for all wood products including garden furniture, staircases, boats, sandwich panels and insulation materials to most common substrates. Suitable for interior and exterior applications.

PU LIQUID 30 MINUTE WOOD GLUE (750ml)

One part moisture cure polyurethane adhesive specially formulated for waterproof bonding. These products are seawater proof are are resistant to acid and chemicals. Conforms to BS EN 204 (Class D4). Sets in 30 minutes.

Application: Excellent bonding properties suitable for all wood products including garden furniture, staircases, boats, sandwich panels and insulation materials to most common substrates. Suitable for interior and exterior applications.

SAVES NAILS SOLVENT-FREE (EU3) WH

Offering less impact on the environment this solvent-free, advanced formula offers instant grab and a tough permanent bond on virtually any porous or non-porous surface. Saves Nails SF  is a low odour, water clean up, construction adhesive which cures to form a high strength bond. Extremely low VOC content, contains no harmful raw materials, making it safer for the environment, safe for the user and safe substrates. Bridges gaps up to 10mm. NOTE: recommended for internal use only.

Application: Ideal for fixing panelling, plasterboard, cove base, window sills, Styrofoam, carpet tack strips, aluminium firring strips, tub surrounds, fireplaces, loose floor/wall tiles, plywood, aluminium, steel, wood, concrete, cork, general repairs to wood, fixing hardboard and plywood and as a general adhesive.

SILICONE RELEASE SPRAY (500ml)

Has a wide range of uses including mould releasing and lubrication in the automotive, engineering, food, clothing and upholstery industries, where the clean, low toxicity lubricating properties of silicone are ideal.

SPRAY LUBRICANT (400ml)

A low viscosity solvent and oil blend, giving excellent penetrating properties. It is a high performance, multi-application fluid which has excellent de-watering, anti-corrosive and general lubricating properties.

Application: For general lubricating of engineering parts.

SUPERGLUE ACTIVATOR (200ml / 400ml)

Accelerates the rate of cure of cyanoacrylate adhesives. Improves bonding to difficult surfaces and prevents penetration of adhesive into porous materials. Speeds strength development.

EASYCLAD 400

A two-component polyurethane adhesive. The formulation has been designed to give ease of mixing for notched scraper applications.

This filled adhesive has been formulated for the bonding of uPVC and GRP sheets to most building substrates, including brickwork, plaster, concrete, blockwork, etc.

Click to download Bond-It catalogue

For technical data or COSHH sheets please contact us on 028 9038 2223 or sales@laydex.com